http://lane.sdsu.edu Fig. 1   Erosion to bedrock downstream of sediment retention dam.

THE LANE RELATION REVISITED

Victor M. Ponce

Professor of Civil Engineering

San Diego State University



ABSTRACT

The Lane relation of fluvial hydraulics is derived from basic principles of sediment transport. It is expressed as follows:

Qs (ds/R)1/3 γ Qw So

Unlike the original Lane relation, this new relation is dimensionless.

INTRODUCTION

This article revisits the Lane relation of fluvial hydraulics (Lane, 1955):

 Qs ds ∝ Qw So (1)

The new relation is derived from theory, and expressed as a dimensionless equation, with the particle size (ds) replaced by the relative roughness function (ds/R)1/3. The derivation follows.

THE FRICTION FUNCTION

The quadratic friction law is (Ponce and Simons, 1977):

 τo = ρ f v2 (2)

in which f is a friction factor equal to 1/8 of the Darcy-Weisbach friction factor.

The bottom shear stress in terms of hydraulic variables is (Chow, 1959):

 τo = γ R So (3)

Combining Eqs 2 and 3:

 So = f v2 / (gR) (4)

The Froude number is (Chow, 1959):

 F = v / (gD)1/2 (5)

Combining Eqs. 4 and 5:

 So = f (D/R) F2 (6)

For a hydraulically wide channel: D ≅ R. Therefore:

 So = f F2 (7)

THE SEDIMENT TRANSPORT FUNCTION

A general sediment transport function is (Ponce, 1988):

 qs = ρ k1 vm (8)

According to Colby (1964), the exponent m varies in the range 3 ≤ m ≤ 7, with the lower values corresponding to high discharges, and the higher values to low discharges.

Assume m = 3 as a first approximation (high water and sediment discharge). In this case, the sediment transport function is:

 qs = ρ k1 v3 (9)

where k1 is a dimensionless constant.

The unit-width discharge is:

 q = v d (10)

The sediment concentration is:

 Cs = qs/(γq) (11)

Combining Eqs. 9 and 11:

 Cs = k1 v2/(gd) (12)

For a hydraulically wide channel, d ≅ D. Combining Eqs. 5 and 12, the sediment concentration is:

 Cs = k1 F2 (13)

Combining Eqs. 7 and 13:

 Cs = k1 (So/f) (14)

The relationship between f and Manning's n is, in SI units (Chow, 1959):

 f = gn2 / R1/3 (15)

In U.S. Customary units:

 f = gn2 / [1.4862 R1/3] (16)

Thus, in general:

 f = k2 n2 / R1/3 (17)

In SI units:

 k2 = g = 9.81 (18)

In U.S. Customary units:

 k2 = g/1.4862 = 32.17 / 2.208 = 14.568 (19)

THE STRICKLER RELATION

The Strickler relation between Manning n and mean particle size d50 is (Chow, 1959):

 n = k3 d501/6 (20)

In SI units:

 k3 = 0.04169 (21)

with d50 in meters.

In U.S. Customary units:

 k3 = 0.0342 (22)

with d50 in feet.

Assume ds = d50:

 n = k3 ds1/6 (23)

 n2 = k32 ds1/3 (24)

Combining Eqs. 17 and 24:

 f = k2 k32 (ds/R)1/3 (25)

THE SEDIMENT CONCENTRATION

The sediment concentration is:

 Cs = k1 (So/f) (14)

Substituting Eq. 25 on Eq. 14:

 Cs = k1 So/[k2 k32 (ds/R)1/3] (26)

Thus:

 Cs = [k1/(k2 k32)] [So/(ds/R)1/3] (27)

Therefore:

 Qs/(γQw) = [k1/(k2 k32)] [So/(ds/R)1/3] (28)

and:

 Qs (ds/R)1/3 = [k1/(k2 k32)] γ Qw So (29)

THE MODIFIED LANE RELATION

The Lane relation (Lane, 1955) is:

 Qs ds ∝ Qw So (1)

Following Eq. 29, the Modified Lane relation is:

 Qs (ds/R)1/3 ∝ γ Qw So (30)

The sediment transport relation is:

 Qs = [k1/(k2 k32)] γ Qw So (R/ds)1/3 (31)

In SI units:

 Qs = [k1/(9.81 × 0.041692)] γ Qw So (R/ds)1/3 (32)

 Qs = 58.7 k1 γ Qw So (R/ds)1/3 (33)

In U.S. Customary units:

 Qs = [k1/(14.568 × 0.03422)] γ Qw So (R/ds)1/3 (34)

 Qs = 58.7 k1 γ Qw So (R/ds)1/3 (35)

The sediment transport function is dimensionless; therefore, independent of the system of units.

The sediment transport parameter k1 is the only one to be determined by calibration. Experience shows that this parameter varies typically in the range 0.001 ≤ k1 ≤ 0.01.

APPLICATIONS

Assume pre- and post-development cases, with subscripts 1 and 2, respectively. Further define:

 a = Qs2/Qs1 (36)

 b = ds2/ds1 (37)

 c = R2/R1 (38)

 d = Qw2/Qw1 (39)

 e = So2/So1 (40)

From the modified Lane relation (Eq. 30):

 a (b/c)1/3 = d e (41)

Thus, the slope change is:

 e = (a/d) (b/c)1/3 (42)

Example 1

A river reach downstream of a channel diversion intake, with d = 0.9, and a = 0.99, b = 1., and c = 0.95, will result in e = 1.12 (aggradation).

Example 2

A river reach downstream of a sediment retention basin, with a = 0.3, and b = 1., c = 0.95, and d = 0.9, will result in e = 0.34 (degradation). In practice, the latter may be limited by geologic controls (armoring or bedrock) (Fig. 1).

REFERENCES

Chow, V. T., 1959. Open-channel hydraulics. Mc-Graw-Hill, New York.

Colby, B. R., 1964. Discharge of sands and mean velocity relations in sand-bed streams. U.S. Geological Survey Professional Paper No. 462-A, Washington, D.C.

Lane, E. W., 1955. The importance of fluvial morphology in hydraulic engineering. Proceedings, American Society of Civil Engineers, No. 745, July.

Ponce, V. M., and D. B. Simons, 1977. Shallow wave propagation in open channel flow. American Society of Civil Engineers Journal of the Hydraulics Division, Vol. 103, No. HY12, December.

Ponce, V. M., 1988. Ultimate sediment concentration. Proceedings, National Conference on Hydraulic Engineering, Colorado Springs, Colorado, August 8-12, 1988, 311-315.

NOTATION

a, b, c, d, e = ratios of post- and pre-development hydraulic variables;

C = Chezy coefficient;

Cs = sediment concentration;

d = flow depth;

D = hydraulic depth;

ds = particle size;

d50 = mean particle size;

f = friction factor equal to 1/8 of Darcy-Weisbach friction factor;

F = Froude number;

g = gravitational acceleration;

k1 = dimensionless sediment transport parameter;

k2 = friction parameter;

k3 = coefficient in the Strickler relation;

n = Manning's friction coefficient;

q = unit-width water discharge;

qs = unit-width sediment discharge;

Qw = water discharge;

Qs = sediment discharge;

R = hydraulic radius;

So = bottom slope;

v = mean velocity;

γ = unit weight of water;

ρ = density of water; and

τo = bottom shear stress. Fig. 2   Sediment deposition at tail of reservoir.

http://lane.sdsu.edu